q is for quandie

On what proved to be the coldest day of the winter so far (windchills of more than 30 degrees below zero), my friend Meggan and I decided to do some thrifting.  I believe we officially qualify for ‘die hard’ status now, don’t you?  But our local thrift store was having a 50% off preview day for members only (we are members), so we had to check it out.  This piece proved to be the ‘find of the day’.

Can you see the giant flaw?  Lower right corner? A huge chunk of trim was ripped off.

But the price on this was really right at a mere $15.  And I could just picture using the same label cup pulls that I used on the book page dresser on it.  Most of all, I knew that my handyman neighbor Ken was up for the challenge of repairing that trim.

Sure enough, I sent it home with Ken and a few days later he sent it back over with this patch job …

Super impressive, right?  Honestly, this kind of repair just boggles my mind.  I don’t know how he does it, and I can’t even begin to explain it.  Let’s just reiterate how very lucky I am to have Ken living next door and leave it at that.

Once that repair was done, next I removed all of the knobs and filled the holes with wood filler.  The fill didn’t have to be perfect because the holes are behind the new label holder cup pulls.  With a ‘label’ in place, you can’t even see them, but if you take the book page paper labels out you can.  So I filled them.  I then sanded the whole piece.  The existing finish was a little shiny and I wasn’t sure how milk paint would react with it, so when in doubt I tend to sand.

Next came a simple paint job using two coats of Miss Mustard Seed’s Typewriter.  I sanded to distress and added a top coat of hemp oil.

Here is how that front repaired section looks after the paint job.

If you didn’t know it was there, I don’t think you would really notice it.  But it does stand out a little in so far as it isn’t as distressed as the rest of the piece.  Had I been really meticulous I should have stained the new wood first, then painted over it.

Once the paint job was finished it was time to attach the new label holder cup pulls.

Ken taught me a little trick to making sure they all lined up properly using a combination square.  Do you have one of these?  I bought mine at a garage sale for a couple of bucks, of course.  It looks like this …

Basically you loosen up the tightening thingie which allows the slide-y part to move along the ruler part (I’m so technical!).  In my case, I then decided exactly how far down from the top of the drawer I wanted to place the pulls.  Once you have that measurement, you tighten it back up.  Now it’s easy to measure for the placement of each pull …

Just rest the flat edge of the slide-y part along the top of your drawer, then butt your label pull up to the bottom of the ruler part.  You can slide the square along making sure that the pull is straight all the way across.  Does that make sense?  I then used a pencil to mark the holes for the screws, pre-drilled small holes, and then screwed the pulls on.

This worked great for the top to bottom placement, as for the side to side placement, I just eye-balled it.  That could probably have backfired for me, but I did it carefully and was able to keep each pull centered on it’s faux drawer.  I think I did a pretty good job keeping them all lined up.  When I mentioned this to Ken, he asked me if my arm hurt.  I thought he meant from having to attach so many pulls, which wasn’t really that hard, so I said “no, not really” and he said, “oh, I thought it might hurt from all that patting yourself on the back!”  Ha!  Yes, it’s true, I was overly proud of myself for getting these all on straight.

I used more Swedish bible book pages to fill the slots for labels.

Are you wondering what makes this a ‘faux’ card catalogue?  It’s because those aren’t really small drawers.  Each set of 4 across is really just one drawer.

So much more functional than lots of small drawers!  Although I did once see a real card catalogue turned into a wine cabinet.  Each drawer held one bottle of wine.  That was pretty cool.  But this piece is really just a small dresser.  I think it’s the perfect size to use as a bedside table.  It would also work great in a foyer or as a TV stand.  I also like the idea of using it in your home office with your printer on top and various office supplies inside.  There are so many possibilities for a small chest of this size.

How do you like my chalkboard?  This was a fun little project of its own!  The frame actually belonged to a mirror that came attached to the book page dresser.  I took it off the dresser.  The size wasn’t the right scale for it.  Plus it was poorly attached.  I had to wonder if it was even original to the dresser.  So, it never went back on.  Later I removed the mirror from the frame and replaced it with some hardboard painted with chalkboard paint.  Then I added a little brass number plate to the frame (at the bottom).  Next I got out the Complete Book of Chalk Lettering that my sister gave me for my birthday and did some more practicing.  I love how it turned out!

My chalkboard skills are slowly improving.

These make a great pair, don’t you think?

Both the chalkboard and the little chest of drawers are available for sale (chest of drawers is SOLD).  If interested, leave a comment and I’ll email you with details.

Remember I told you that I sent Mr. Q after two dressers recently?  The first was the ‘how chippy is too chippy’ dresser from last week, and this is the second.

Before getting started on the paint job, there was a small fix on this one that Ken helped me out with.  This dresser must have originally had a mirror.  It would have been mounted onto the back and the mounting would have fit into two notches cut into the top of the dresser at the back.  I did a crappy job taking photos of the fix, so you’ll have to excuse the poor picture.

The lighter piece is an insert that Ken cut to fit the notch.  He used glue to hold it in place, along with a few nails driven in from the back.  I then patched the edges with another new wood filler I’m trying, Elmer’s ProBond in Walnut.

These are the kinds of flaws that make pieces good candidates for painting.  If one wanted to strip and stain this piece, you’d have those two big notches at the back of the top.  Do you try to match the wood?  Do you leave the notches?  Either way you’d probably end up with a so-so end result.  But with paint, the repair is barely even noticeable.  In fact, you might roll your eyes in disbelief, but I totally forgot about this repair by the time I had this painted.  It wasn’t until I started editing the photos for this post that I remembered, ‘oh yeah, Ken fixed this one.’

See, you can’t even tell there is a patch back there can you?

As you can see in the ‘before’ photo, the existing stain on this dresser was dark, dark, dark and had a slightly reddish tinge.  I was fully prepared for it to be one of the dreaded ‘bleeders’.  You know, where the stain bleeds through the paint?  I was pleasantly surprised to find that it was not.  My course of action when I have a piece that might bleed is to paint the first coat and then watch for bleeding.  If I see stain coming through the first coat of paint, then I seal it before moving on to coat number two.  In this case, my plan payed off.  No bleeding after the first coat meant I didn’t have to seal this one, thus saving myself the cost of sealer and the time spent to apply it.

If you’ve been following me for a while, you might know that my usual philosophy is to not fight against the existing color of pieces.  In other words, with a finish this dark to begin with I would usually paint it in a dark color.  Originally I was leaning towards Miss Mustard Seed’s Typewriter (black).  Or possibly the Little Billy Goat Prizewinner (dark blue).  But in the end, this dresser was crying out for light (or maybe that was just me projecting my own feelings onto an inanimate object on a dreary winter day).

After reviewing my paint inventory, I pulled out Fusion’s Inglenook.  Good grief I love this color!  It’s just so pretty.

In addition to being pretty, I am once again impressed with Fusion’s coverage.  It did take two coats to cover this piece, but look again at how dark it started out!  Going this light in two coats is pretty impressive.

And of course, the second real benefit of the Fusion, I didn’t have to use a top coat!  I sanded the edges for a distressed look and I was done.  I accomplished this makeover (not including Kens’ repair) in two evenings after work.  The first evening I removed hardware, lightly sanded, wiped it down with TSP substitute and painted the first coat.  The second evening I painted a 2nd coat of paint before dinner, watched an episode of The Blacklist (James Spader, who remembers when he had hair?) while it dried, sanded the edges and replaced the hardware.  Bam!  Done!

Isn’t this dresser just a little charmer?  I love that curved bottom on the lowest drawer, and the curve of the front two legs.  This piece is just full of subtle curves.  I purposely left the paint job simple so that the design of the dresser could speak for itself.

You’ll notice that I replaced the hardware with glass knobs.  The wood knobs were still in good shape.  I could have opted to just paint them and put them back on.  In fact, I most likely would have done that had I chosen a dark color for this one.  But this color was calling out for pretty glass knobs.  Right?

Like adding sparkly jewelry to a pretty outfit.

This vintage alarm clock was the perfect color to use for staging.

It’s still set to midnight from New Year’s Eve!

So what do you think?  It’s hard not to be charmed by this pretty little dresser isn’t it?

Linked up with:  the FAB Friday link party.

Thanks so much to everyone who took the time to leave a comment regarding the question of drawer pulls last week.  Pressed brass drawer pulls, should they stay or should they go now?  If they go there will be trouble, if they stay it will be double … is anyone else singing along?  For those of you not old enough, that song is by The Clash and was written in 1981.  I’m pretty sure it wasn’t about drawer pulls though.

Well, to clear up any mystery, here are the actual drawer pulls in question.

And I’m guessing that some of you might be tempted to think that was a ‘before’ picture, but no, it’s not.  Thus leading to today’s question.  How chippy is too chippy?

Let’s start at the beginning though, shall we?

A week or two ago I found three dressers in one day on craigslist.  Two were even right here in my own hometown, which was pretty awesome.  It was also Mr. Q’s day off, so he was free to run around picking them up.  In the end, we only purchased two of them.  The third was a little overpriced and the seller wasn’t budging on the asking price, so Mr. Q passed on it.  This dresser is the first one he purchased that day.

As you can see, it had that ugly orange-y/reddish stain.  I am not a fan.  Job no. 1 was to strip the top and then wax it.  Easy enough.

Turned out beautifully.

Next step was to paint the body in Miss Mustard Seed milk paint.  Those of you who follow Miss Mustard Seed have probably been reading about the new color she has coming out, Farmhouse White.  I was so wishing I had that color for this dresser!  But no, I am just impatiently waiting for it like most everyone else.  Meanwhile, since I’d had such good luck with the Marzipan and leaving it unwaxed (on the book page dresser), I chose to go with that color again.  I was aiming for a chippy, vintage farmhouse look, so I opted not to pre-sand.  I did wipe the dresser down with some TSP substitute though.

I have to say, even after having painted, let’s see, maybe close to 100 pieces of furniture in milk paint, I still often can’t predict the end result.  I suspected I would get some chipping.  I wanted plenty of chipping.  What I got was A LOT of chipping.

Personally, my heart still skips a little beat whenever I see an awesomely chippy piece of furniture.  One of my own favorite pieces is this chippy cupboard that resides out in my photo cottage.

Recently I saw a very similar cupboard (much taller, but the doors were missing) for sale at my local Bachman’s and the price tag said $1,000 (Maplewood location in case any of you locals want to rush out and buy it).  No lie.

So when I saw how chippy this dresser turned out, I thought it was pretty fab.  My sister wasn’t so sure.

I could have opted to sand this all down to the wood and start over.  I have done that before and in general once you do the sanding necessary to take all of the paint off, the next coats of paint tend to adhere pretty well (not always, but generally).

But I was kind of loving the chippy.

When my friend Meggan dropped by to pick me up for some thrifting, she voted a resounding yes on the chippy as well!  So how about you?  Chippy yes or chippy no?

Lots of ironstone seemed like the right choice for staging this dresser.

Along with some old books and wooden utensils.

As for the drawer pulls, there were a couple of comments left on my last post about them that really made sense to me.  Kim made a comment about creating the look I want with the dresser and then deciding on the hardware.  And Nikkii’s comment about choosing a style really clicked with me.  I realized that this dresser was going to be vintage farmhouse all the way!

I think the existing pressed brass drawer pulls totally work with the chippy, vintage farmhouse vibe of this dresser.  I hope you agree!

This dresser is available for sale by the way.  If you are local and interested, feel free to leave a comment and I will be happy to email you with the details.